WEKO3
アイテム
{"_buckets": {"deposit": "d81ed365-d2ec-4a87-b348-1ba776f1e2e5"}, "_deposit": {"id": "12974", "owners": [], "pid": {"revision_id": 0, "type": "depid", "value": "12974"}, "status": "published"}, "_oai": {"id": "oai:soar-ir.repo.nii.ac.jp:00012974", "sets": []}, "author_link": ["39756"], "item_10_biblio_info_6": {"attribute_name": "書誌情報", "attribute_value_mlt": [{"bibliographicIssueDates": {"bibliographicIssueDate": "1972-12-25", "bibliographicIssueDateType": "Issued"}, "bibliographicPageEnd": "185", "bibliographicPageStart": "163", "bibliographicVolumeNumber": "33", "bibliographic_titles": [{"bibliographic_title": "信州大学工学部紀要"}]}]}, "item_10_description_20": {"attribute_name": "抄録", "attribute_value_mlt": [{"subitem_description": "Involute face gears are usually employed for connecting the intersecting shafts or the skew shafts. This gear set is made of an involute spur pinion or helical involute pinion meshing with a face gear that is generated by a pinion cutter of the same size and form as the mating involute spur pinion or a helical involute pinion. One of the principal design problems in the face gears is to calculate the face width of the face gears. The maximum outside diameter of the face gear is limited by the point where the top land of the tooth narrows to a knife-edge, and the minimum inside diameter is limited by the point where the undercut exists in the tooth profile of the face gear. In designing the face gearsets, the following conditions should be fulfilled : (a) The crest of the face gear should not be sharpened. (b) The undercut should not exist in the tooth form of the face gear. (c) The involute interference should be avoided. (d) The contact ratio should be larger than 1.0. An analytical study on these subjects in the helical involute face gear is made by the author, and a pack of the synthetic diagrams available for the design and production of the helical involute face gearset is prepared. These synthetic diagrams are used for determining the maximum outside diameter, the minimum inside diameter and the face width of the face gear. The author shows some numerical examples with a view to facilitating the practical utilization of these diagrams, and the face gearsets are made by using the synthetic diagrams presented in this paper.", "subitem_description_type": "Abstract"}]}, "item_10_description_30": {"attribute_name": "資源タイプ(コンテンツの種類)", "attribute_value_mlt": [{"subitem_description": "Article", "subitem_description_type": "Other"}]}, "item_10_description_31": {"attribute_name": "フォーマット:mimeタイプ", "attribute_value_mlt": [{"subitem_description": "application/pdf", "subitem_description_type": "Other"}]}, "item_10_description_5": {"attribute_name": "引用", "attribute_value_mlt": [{"subitem_description": "信州大学工学部紀要 33: 163-185 (1972)", "subitem_description_type": "Other"}]}, "item_10_publisher_4": {"attribute_name": "出版者", "attribute_value_mlt": [{"subitem_publisher": "信州大学工学部"}]}, "item_10_select_64": {"attribute_name": "著者版フラグ", "attribute_value_mlt": [{"subitem_select_item": "publisher"}]}, "item_10_source_id_35": {"attribute_name": "ISSN", "attribute_value_mlt": [{"subitem_source_identifier": "0037-3818", "subitem_source_identifier_type": "ISSN"}]}, "item_10_source_id_39": {"attribute_name": "NII ISSN", "attribute_value_mlt": [{"subitem_source_identifier": "0037-3818", "subitem_source_identifier_type": "ISSN"}]}, "item_10_source_id_40": {"attribute_name": "書誌レコードID", "attribute_value_mlt": [{"subitem_source_identifier": "AN00121228", "subitem_source_identifier_type": "NCID"}]}, "item_10_text_66": {"attribute_name": "sortkey", "attribute_value_mlt": [{"subitem_text_value": "12"}]}, "item_1627890569677": {"attribute_name": "出版タイプ", "attribute_value_mlt": [{"subitem_version_resource": "http://purl.org/coar/version/c_970fb48d4fbd8a85", "subitem_version_type": "VoR"}]}, "item_creator": {"attribute_name": "著者", "attribute_type": "creator", "attribute_value_mlt": [{"creatorNames": [{"creatorName": "両角, 宗晴", "creatorNameLang": "ja"}], "nameIdentifiers": [{"nameIdentifier": "39756", "nameIdentifierScheme": "WEKO"}]}]}, "item_files": {"attribute_name": "ファイル情報", "attribute_type": "file", "attribute_value_mlt": [{"accessrole": "open_date", "date": [{"dateType": "Available", "dateValue": "2015-09-28"}], "displaytype": "detail", "download_preview_message": "", "file_order": 0, "filename": "Engineering33-12.pdf", "filesize": [{"value": "1.3 MB"}], "format": "application/pdf", "future_date_message": "", "is_thumbnail": false, "licensetype": "license_note", "mimetype": "application/pdf", "size": 1300000.0, "url": {"label": "Engineering33-12.pdf", "url": "https://soar-ir.repo.nii.ac.jp/record/12974/files/Engineering33-12.pdf"}, "version_id": "e3fbf280-4f39-4dea-bcbe-262003a200ed"}]}, "item_language": {"attribute_name": "言語", "attribute_value_mlt": [{"subitem_language": "jpn"}]}, "item_resource_type": {"attribute_name": "資源タイプ", "attribute_value_mlt": [{"resourcetype": "departmental bulletin paper", "resourceuri": "http://purl.org/coar/resource_type/c_6501"}]}, "item_title": "ヘリカルインボリュートフェースギアの研究", "item_titles": {"attribute_name": "タイトル", "attribute_value_mlt": [{"subitem_title": "ヘリカルインボリュートフェースギアの研究", "subitem_title_language": "ja"}, {"subitem_title": "Study on Helical Involute Face Gear", "subitem_title_language": "en"}]}, "item_type_id": "10", "owner": "1", "path": ["1274"], "permalink_uri": "http://hdl.handle.net/10091/11764", "pubdate": {"attribute_name": "PubDate", "attribute_value": "2011-02-15"}, "publish_date": "2011-02-15", "publish_status": "0", "recid": "12974", "relation": {}, "relation_version_is_last": true, "title": ["ヘリカルインボリュートフェースギアの研究"], "weko_shared_id": -1}
ヘリカルインボリュートフェースギアの研究
http://hdl.handle.net/10091/11764
http://hdl.handle.net/10091/1176486eb1056-94b6-40ca-88b2-0d1fffc1cb7c
名前 / ファイル | ライセンス | アクション |
---|---|---|
![]() |
|
Item type | 紀要論文 / Departmental Bulletin Paper(1) | |||||
---|---|---|---|---|---|---|
公開日 | 2011-02-15 | |||||
タイトル | ||||||
言語 | ja | |||||
タイトル | ヘリカルインボリュートフェースギアの研究 | |||||
タイトル | ||||||
言語 | en | |||||
タイトル | Study on Helical Involute Face Gear | |||||
言語 | ||||||
言語 | jpn | |||||
資源タイプ | ||||||
資源 | http://purl.org/coar/resource_type/c_6501 | |||||
タイプ | departmental bulletin paper | |||||
著者 |
両角, 宗晴
× 両角, 宗晴 |
|||||
出版者 | ||||||
出版者 | 信州大学工学部 | |||||
引用 | ||||||
内容記述タイプ | Other | |||||
内容記述 | 信州大学工学部紀要 33: 163-185 (1972) | |||||
書誌情報 |
信州大学工学部紀要 巻 33, p. 163-185, 発行日 1972-12-25 |
|||||
抄録 | ||||||
内容記述タイプ | Abstract | |||||
内容記述 | Involute face gears are usually employed for connecting the intersecting shafts or the skew shafts. This gear set is made of an involute spur pinion or helical involute pinion meshing with a face gear that is generated by a pinion cutter of the same size and form as the mating involute spur pinion or a helical involute pinion. One of the principal design problems in the face gears is to calculate the face width of the face gears. The maximum outside diameter of the face gear is limited by the point where the top land of the tooth narrows to a knife-edge, and the minimum inside diameter is limited by the point where the undercut exists in the tooth profile of the face gear. In designing the face gearsets, the following conditions should be fulfilled : (a) The crest of the face gear should not be sharpened. (b) The undercut should not exist in the tooth form of the face gear. (c) The involute interference should be avoided. (d) The contact ratio should be larger than 1.0. An analytical study on these subjects in the helical involute face gear is made by the author, and a pack of the synthetic diagrams available for the design and production of the helical involute face gearset is prepared. These synthetic diagrams are used for determining the maximum outside diameter, the minimum inside diameter and the face width of the face gear. The author shows some numerical examples with a view to facilitating the practical utilization of these diagrams, and the face gearsets are made by using the synthetic diagrams presented in this paper. | |||||
資源タイプ(コンテンツの種類) | ||||||
内容記述タイプ | Other | |||||
内容記述 | Article | |||||
ISSN | ||||||
収録物識別子タイプ | ISSN | |||||
収録物識別子 | 0037-3818 | |||||
書誌レコードID | ||||||
収録物識別子タイプ | NCID | |||||
収録物識別子 | AN00121228 | |||||
出版タイプ | ||||||
出版タイプ | VoR | |||||
出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 |