{"_buckets": {"deposit": "7cabec9c-1a7a-44ad-b5e4-8ede922bcbdb"}, "_deposit": {"id": "13043", "owners": [], "pid": {"revision_id": 0, "type": "depid", "value": "13043"}, "status": "published"}, "_oai": {"id": "oai:soar-ir.repo.nii.ac.jp:00013043", "sets": []}, "author_link": ["39871"], "item_10_biblio_info_6": {"attribute_name": "書誌情報", "attribute_value_mlt": [{"bibliographicIssueDates": {"bibliographicIssueDate": "1969-12-25", "bibliographicIssueDateType": "Issued"}, "bibliographicPageEnd": "156", "bibliographicPageStart": "139", "bibliographicVolumeNumber": "27", "bibliographic_titles": [{"bibliographic_title": "信州大学工学部紀要"}]}]}, "item_10_description_20": {"attribute_name": "抄録", "attribute_value_mlt": [{"subitem_description": "One of the principal design problems in the internal face gears is to calculate the face width of the internal face gears. The maximum outside diameter of the internal face gear is limited by the point where the top land of the tooth narrows to a knife-edge, and the minimum inside diameter is limited by the point where the undercut exists in the tooth profile of the internal face gear. In designing the internal face gearsets, the following conditions should be satisfied : (a) The crest of the internal face gear should not be sharpened. (b) The undercut should not exist in the tooth form of the internal face gear. (c) The involute interference should be avoided. (d) The contact ratio should be larger than 1. 0. An analytical study on these subjects mentioned above in the internal face gear is treated by the author, and a pack of the synthetic diagrams available for the design and production of the internal face gearset are prepared. These synthetic diagrams are used for determining the maximum outside diameter, the minimum inside diameter and the face width of the internal face gear. The author shows some numerical examples with a view to facilitating the practical utilization of these diagrams, and the internal face gearsets are made by using the synthetic diagrams presented in this paper.", "subitem_description_type": "Abstract"}]}, "item_10_description_30": {"attribute_name": "資源タイプ（コンテンツの種類）", "attribute_value_mlt": [{"subitem_description": "Article", "subitem_description_type": "Other"}]}, "item_10_description_31": {"attribute_name": "フォーマット：mimeタイプ", "attribute_value_mlt": [{"subitem_description": "application/pdf", "subitem_description_type": "Other"}]}, "item_10_description_5": {"attribute_name": "引用", "attribute_value_mlt": [{"subitem_description": "信州大学工学部紀要 27: 139-156 (1969)", "subitem_description_type": "Other"}]}, "item_10_publisher_4": {"attribute_name": "出版者", "attribute_value_mlt": [{"subitem_publisher": "信州大学工学部"}]}, "item_10_select_64": {"attribute_name": "著者版フラグ", "attribute_value_mlt": [{"subitem_select_item": "publisher"}]}, "item_10_source_id_35": {"attribute_name": "ISSN", "attribute_value_mlt": [{"subitem_source_identifier": "0037-3818", "subitem_source_identifier_type": "ISSN"}]}, "item_10_source_id_39": {"attribute_name": "NII ISSN", "attribute_value_mlt": [{"subitem_source_identifier": "0037-3818", "subitem_source_identifier_type": "ISSN"}]}, "item_10_source_id_40": {"attribute_name": "書誌レコードID", "attribute_value_mlt": [{"subitem_source_identifier": "AN00121228", "subitem_source_identifier_type": "NCID"}]}, "item_10_text_66": {"attribute_name": "sortkey", "attribute_value_mlt": [{"subitem_text_value": "09"}]}, "item_1627890569677": {"attribute_name": "出版タイプ", "attribute_value_mlt": [{"subitem_version_resource": "http://purl.org/coar/version/c_970fb48d4fbd8a85", "subitem_version_type": "VoR"}]}, "item_creator": {"attribute_name": "著者", "attribute_type": "creator", "attribute_value_mlt": [{"creatorNames": [{"creatorName": "両角,  宗晴", "creatorNameLang": "ja"}], "nameIdentifiers": [{"nameIdentifier": "39871", "nameIdentifierScheme": "WEKO"}]}]}, "item_files": {"attribute_name": "ファイル情報", "attribute_type": "file", "attribute_value_mlt": [{"accessrole": "open_date", "date": [{"dateType": "Available", "dateValue": "2015-09-28"}], "displaytype": "detail", "download_preview_message": "", "file_order": 0, "filename": "Engineering27-09.pdf", "filesize": [{"value": "1.2 MB"}], "format": "application/pdf", "future_date_message": "", "is_thumbnail": false, "licensetype": "license_note", "mimetype": "application/pdf", "size": 1200000.0, "url": {"label": "Engineering27-09.pdf", "url": "https://soar-ir.repo.nii.ac.jp/record/13043/files/Engineering27-09.pdf"}, "version_id": "fb4e32a4-3bd8-41a1-ba9a-7ad60456fc73"}]}, "item_language": {"attribute_name": "言語", "attribute_value_mlt": [{"subitem_language": "jpn"}]}, "item_resource_type": {"attribute_name": "資源タイプ", "attribute_value_mlt": [{"resourcetype": "departmental bulletin paper", "resourceuri": "http://purl.org/coar/resource_type/c_6501"}]}, "item_title": "内接フェースギヤの研究", "item_titles": {"attribute_name": "タイトル", "attribute_value_mlt": [{"subitem_title": "内接フェースギヤの研究", "subitem_title_language": "ja"}, {"subitem_title": "Study on Internal Face Gear", "subitem_title_language": "en"}]}, "item_type_id": "10", "owner": "1", "path": ["1280"], "permalink_uri": "http://hdl.handle.net/10091/11745", "pubdate": {"attribute_name": "PubDate", "attribute_value": "2011-02-15"}, "publish_date": "2011-02-15", "publish_status": "0", "recid": "13043", "relation": {}, "relation_version_is_last": true, "title": ["内接フェースギヤの研究"], "weko_shared_id": -1}